Main product image for Resol VBus to UART Board – Home Assistant ESPHome
Product image 1 for Resol VBus to UART Board – Home Assistant ESPHome
Product image 2 for Resol VBus to UART Board – Home Assistant ESPHome
Product image 3 for Resol VBus to UART Board – Home Assistant ESPHome
Product image 4 for Resol VBus to UART Board – Home Assistant ESPHome
Assembled Resol VBus interface board — read your solar thermal controller into Home Assistant via ESPHome. Add an ESP32.
ESP32
Home automation
WiFi

Bring your Resol solar controller into Home Assistant.

An assembled interface board that reads the VBus data from Resol / DeltaSol solar thermal controllers and converts it to clean UART for an ESP32 (or ESP8266) running ESPHome. Wire it up and pull your solar system's live data — up to four temperature sensors, two pump-speed channels, operating hours and heat quantity — straight into Home Assistant.

Rolling your own means a minimum board order, a two-week wait, sorting the BOM and placement files, then working out the VBus data offsets to get a reading. This one is done: SMD parts machine-fitted (not hand-soldered), tested, and ready to wire in.

What you get

Fully assembled, tested board Header pins included — VBus is a simple 2-wire, non-polarised connection A ready-to-use ESPHome config for the DeltaSol BS/2 HE (and rebadges such as Joule)

You supply An ESP32 (or similar) and a few jumper wires. The board runs off the ESP's 3.3 V — no separate supply.

Wiring

2-pin (U8) → controller VBus terminals (non-polarised) 3-pin (J5) → ESP: VCC → 3.3 V · DATA → UART RX (e.g. GPIO16) · GND → GND

Compatibility The board reads any Resol / DeltaSol VBus controller — the same unit is rebadged worldwide, so it may not say "Resol" on the front. In Europe it's also sold as Viessmann / Vitosolic, Sonnenkraft, Kingspan, De Dietrich, Caleffi and others; in Australia as Apricus, Thermann and Dux; in the US / Canada it's usually badged Resol / DeltaSol directly, or Caleffi iSolar. Many DeltaSol models (BS Plus, BS/2, C, CS2, CS4, CS Plus) are natively supported in ESPHome — just select the model. Other models are read by the board and set up with a short custom config. Not sure about yours? Message me your controller model before buying and I'll tell you straight.

Note: heat-quantity readings need the controller's flow/return sensor fitted — without it, that value reads 0.

Based on the open-source FatBeard VBus design — credit to the original author. Sold as a hobbyist board, no warranty.

Links to code and documentation

Documentation (esphome.io)

Product HS Code: 847330

Shipping policy

Orders ship from Dublin, Ireland via An Post, usually within 1–2 working days. Standard Post is untracked.

Typical delivery times: Ireland 1–3 days, UK and EU 1–2 weeks, Canada/Australia/NZ 2–3 weeks.

EU and Northern Ireland orders have no customs charges. Orders to Great Britain and outside the EU are sent with a customs declaration.

This product does not ship to United States.

Resol VBus to UART Board – Home Assistant ESPHome

Sold by Solbus

$30.77

No tax for United States [change]
Stock available: 10
Check
Original Design
This product was designed by Solbus. By buying this product you support original hardware creators.

The seller

Solbus

Solbus logo

Dublin, Ireland
1 order since Nov 5, 2026
Small-batch Home Assistant hardware, designed and built in Ireland.
SolBus makes interface boards that bring heating and solar controllers into Home Assistant via ESPHome — starting with Resol VBus (DeltaSol and its rebadges: Viessmann, COSMO, Caleffi, Sonnenkraft, Firebird and more). It began as a board I built to get my own solar system into Home Assistant.
• Honest about compatibility — message me with your controller model before ordering and I'll tell you straight whether it's supported.
• Built on open source — with full credit to the original open-hardware projects.
• Tested before shipping, posted from Ireland via An Post.